WhatsApp
Request a Quote
Leave Your Message
Customer Case | 4U Rackmount PC Selection for a Semiconductor Equipment Company
Customer Stories

Customer Case | 4U Rackmount PC Selection for a Semiconductor Equipment Company

2026-09-17
Table of Contents


Introduction

Selecting an industrial computer for semiconductor equipment is rarely just a matter of choosing the fastest processor. Storage redundancy, PCIe expansion, serial communication, memory generation, operating system support, and installation procedures all need to work together.
 
A Malaysia-based semiconductor equipment company faced this challenge when it prepared two different 4U rackmount PC configurations for engineering and equipment-related workloads.
4u-rackmount-pc


Two 4U Rackmount PC Configurations for Different Workloads

The project involved two configurations rather than one standardized system.
 
The first configuration used an Intel Core i7-10700K processor, 16GB of DDR4 memory, two 2TB 7200 RPM hard drives configured for RAID 1, and Windows 11 IoT Enterprise LTSC. It also required multiple RS232 ports, with six ports integrated into the system and two additional ports provided through a PCI expansion card.
 
The second configuration targeted a higher-performance workload. It used an Intel Core i9-14900K processor, 32GB of DDR5 memory, two 1TB SSDs, one 1TB M.2 NVMe SSD, an 850W power supply, and activated Windows 11 IoT Enterprise LTSC 64-bit.
 
The two systems show why a 4U rackmount PC should be configured around the workload rather than selected from a general-purpose specification sheet.
d733e454-f4a4-489a-b720-9551d1
1333397c-48ab-4b4c-910f-065208


PCIe Lane Allocation Changed the Expansion Plan

PCIe expansion was one of the key decision points.
 
The original requirement considered using both x16 and x8 expansion resources at the same time. During the configuration discussion, the available lane arrangement was reviewed and the plan was adjusted toward either one x16 configuration or two x8 configurations.
 
This distinction matters because the number of physical PCIe slots does not always equal the number of slots that can operate at the desired bandwidth simultaneously. For industrial systems connected to acquisition cards, inspection hardware, motion-control devices, or other expansion modules, buyers should confirm the physical slot layout, PCIe generation and lane width, shared bandwidth, simultaneous card operation, power supply, and cooling design.
 
For a platform reference, see the 4U rackmount industrial PC platform.


RAID, NVMe Storage, and Serial I/O Had to Be Checked Together

The storage requirements were not limited to capacity.
 
The first configuration used two hard drives in RAID 1 for data redundancy. The second configuration combined SSD storage with an M.2 NVMe drive for a different performance profile. The customer also requested more information about storage speed and drive performance before finalizing the configuration.
 
Serial communication was another important variable. Instead of treating RS232 as a standard checkbox, the project allocated ports between onboard interfaces and a PCI expansion card. This approach allowed the system to meet the required port count while keeping the rackmount platform adaptable.
 
The SIN-610L-BQ670MA2 4U rackmount PC page provides a public reference for the Q670-based platform, processor support, DDR5 memory, storage interfaces, and RS232 connectivity. Project-specific builds still need to be checked against the final configuration sheet.
 
4u-rackmount-pc-1


Delivery Was Followed by RAID and Boot Validation

After production and delivery, the installation phase revealed an important handover issue.
 
The customer recreated a RAID 1 volume but then encountered difficulty accessing the F11 or F7 boot menu. Different UEFI and Legacy settings were tested, and the system entered a UEFI Interactive Shell. The support process then focused on Windows 11 IoT system files, RAID recreation steps, Intel Rapid Storage Technology drivers, and boot configuration.
 
This part of the case highlights a practical lesson: RAID configuration and operating-system recovery should be included in the delivery checklist. A system can meet the hardware requirements and still require clear guidance on RAID mode selection, recovery media preparation, Intel Rapid Storage Technology drivers, UEFI or Legacy boot modes, boot-menu access, and post-installation verification.


Buyer Takeaways for 4U Rackmount PC Selection

  1. Confirm whether the system needs RAID 1, independent disks, SSDs, or NVMe storage.
  2. Verify whether PCIe cards can operate simultaneously at the required lane width.
  3. Specify which serial ports are onboard and which require an expansion card.
  4. Match the memory generation to the motherboard platform.
  5. Include Windows IoT installation and recovery procedures in the handover.
  6. Check that the final configuration sheet matches the quotation, PO, and delivered system.


Frequently Asked Questions

Q1:What should buyers verify before choosing a 4U rackmount PC for RAID and NVMe storage?

Buyers should confirm the number of SATA and M.2 interfaces, whether the interfaces share bandwidth, supported RAID modes, drive capacity, and the required operating-system recovery method. In this case, one configuration used RAID 1 HDD storage, while another combined SATA SSDs with an M.2 NVMe SSD.
 

Q2:Can a 4U rackmount PC use both PCIe x16 and x8 expansion cards at the same time?

This depends on the motherboard’s PCIe lane allocation. The case showed that the required configuration had to be adjusted between one x16 signal or two x8 signals. Buyers should verify simultaneous lane support instead of counting only the physical slots.
 

Q3:How many RS232 ports can be configured on an industrial rackmount PC?

The number depends on the selected platform and expansion method. One configuration in this case used six onboard RS232 ports plus two additional ports through a PCI expansion card. The final port count should be confirmed in the configuration sheet.
 

Q4:What should be checked after rebuilding a RAID 1 volume?

The installation checklist should include the RAID mode, recovery USB, Windows image, Intel Rapid Storage Technology driver, UEFI or Legacy boot mode, and boot-menu access. These checks became important during the post-delivery installation process in this case.
 

Q5:Can one 4U rackmount PC support both SATA SSDs and an M.2 NVMe SSD?

It can be possible, but the exact answer is platform-specific. The case configuration combined two 1TB SATA SSDs with one 1TB M.2 NVMe SSD. Interface sharing, BIOS support, cooling, and the operating-system installation method should be verified before ordering.

Related Products

LET'S TALK ABOUT YOUR PROJECTS

  • sinsmarttech@gmail.com
  • 3F, Block A, Future Research & Innovation Park, Yuhang District, Hangzhou, Zhejiang, China

Our experts will solve them in no time.